Setup Instructions

Sente Stand

stand-exploded.png__PID:5912473f-59c5-41af-bb3b-10ae903eeaff
  • The Stand is the heaviest item out of all items in the Sente product line. Be sure to have someone help you with any lifting or moving of this box and product!
  • Start by removing the stand from the box. We did this by laying the box on it's flat side, and pulling the stand out.
  • Find the plastic bag of screws and other components packed with the stand. It's likely loose in the box.
IMG_6699.JPEG__PID:953c225b-7ca2-4161-bb8e-1ac01df31bc5

On one side of the stand there are 2 rectangular panels (the door panel, and the base) packed into the foam and plastic wrap. Locate these - depending on how you took your stand out of the packaging these two panels may be on the bottom. If these two panels are not already facing up, use two people to turn the stand over.

Cut the plastic and remove the door panel, setting it aside.

door-panel.png__PID:8e4ee2d5-b71c-4007-8b80-976d348c1912

The base is the heaviest part. This piece is packed with the foam encasing each corner of it. Using two people, remove the base set it down somewhere you can access the threaded holes at each corner.

stand-base.png__PID:1ac01df3-1bc5-4916-ae43-272d298b8e4e

The base has a threaded hole at each corner on the underside. Your bag of components includes 4 levelers. These will help you level the stand, and will also provide extra stability on soft surfaces such as carpet. Using your fingers, screw one into each corner, screwing them in all the way.

levelers.png__PID:272d298b-8e4e-42d5-b71c-e007cb80976d

Once the levelers are on, place the base on the floor and ensure it's sturdy.

If you are planning on using your stand with the RetroGlow Marquee, then skip this next step.

If you are planning on using your stand WITHOUT the RetroGlow Marquee, then you'll want to remove the marquee backer piece at the top of the stand. To do this, simply remove the 4 screws holding it on.

marquee-backer.png__PID:af7e14db-b88f-462e-b4ef-fa504f6e5912
marquee-backer-screws.png__PID:b88fd62e-f4ef-4a50-8f6e-5912473f59c5

Next, using two people, stand up the large tall part of the stand, removing any foam still stuck on it.

Lift this section onto the base, ensuring the square metal tubes on the front are placed onto the prongs on the base.

Screw in the 4 screws that hold the stand onto the base. See the image below for placement of these 4 screws.

base-screws.png__PID:59c581af-bb3b-40ae-903e-eaff093b68ad

This step is optional. If you want the wheels on your stand to make it easy to move around, then proceed, otherwise you're all done!

The wheels are attached to the back of the stand with 8 screws. You'll want to screw in all 8 screws, as the full weight of the stand will be on these screws when you're moving it around.

wheels.png__PID:eaff093b-68ad-4a8a-8bc0-d5e20e9a474a

Mounting The Sente

Your Sente includes the wall mount bracket, which is hooked on the back of your Sente when you unbox it. Remove the wall mount bracket - you don't need it with the Stand.

Once you have remove the wall mount bracket from the back of the Sente, prepare the power cord by passing it through the big hole on the back of your Sente (you'll need to open the lower front door of your Sente in order to access this).

Next, using 2 people you can lift your Sente onto the Stand, making sure to pass the power cable into the stand enclosure just below the lower cross bar.

The two sets of hooks on the back of your Sente match up to the two cross bars on your Stand. Also make sure the top of your Sente hooks onto the upper hooks of the Stand.

From here, you can open the lower door of the Stand and pass the power cable through the hole in the back of the Stand.

Didn't find what you were looking for? Contact us.